Skip to content

EMS control and status registers

Generated from EnergySyc_EMS_ES100Cx12S/emsConfig/ems/ems_register_full.json by EnergySyc_EMS_ES100Cx12S/tools/generate_register_map_docs.py. Do not edit by hand - re-run the generator after changing the register map.

158 registers at @1..@208: 156 read-write (settings and commands) and 2 read-only (status). See the overview page for the write rules that apply to this area.

Register Address Type Regs Access Device Notes
ems_operation_mode @1 INT16U 1 RW ems values: 0 = MANUAL, 1 = ARBITRAGE, 2 = PEAK_SHAVING, 3 = VALLEY_FILLING, 4 = SCHEDULED_CHARGE_DISCHARGE, 5 = BACKUP, 6 = BACKUP_PEAK_SHAVING, 7 = BACKUP_FREQUENCY_REGULATION, 8 = POWER_FACTOR_CORRECTION, 9 = VOLTAGE_SUPPORT, 10 = FREQUENCY_REGULATION, 11 = ANTI_BACKFLOW, 12 = MAINTENANCE, 13 = ENERGY_OPTIMIZATION, 14 = POWER_NODE_ENERGY_SHARING, 15 = GRID_SYNC, 16 = DYNAMIC_LOAD_BALANCING, 17 = IDLE, 18 = STOP_ALL, 19 = PAYLOAD_DIAGNOSTIC_TEST; settings: ems_operation_mode (enum)
ems_control_mode @2 INT16U 1 RW ems values: 0 = local_control, 1 = scada_control, 2 = external_control; settings: ems_control_mode (control_mode)
ems_operation_status @3 INT16U 1 RO ems values: 0 = MANUAL, 1 = ARBITRAGE, 2 = PEAK_SHAVING, 3 = VALLEY_FILLING, 4 = SCHEDULED_CHARGE_DISCHARGE, 5 = BACKUP, 6 = BACKUP_PEAK_SHAVING, 7 = BACKUP_FREQUENCY_REGULATION, 8 = POWER_FACTOR_CORRECTION, 9 = VOLTAGE_SUPPORT, 10 = FREQUENCY_REGULATION, 11 = ANTI_BACKFLOW, 12 = MAINTENANCE, 13 = ENERGY_OPTIMIZATION, 14 = POWER_NODE_ENERGY_SHARING, 15 = GRID_SYNC, 16 = DYNAMIC_LOAD_BALANCING, 17 = IDLE, 18 = STOP_ALL, 19 = PAYLOAD_DIAGNOSTIC_TEST; unset in the settings file (serves 0)
control_settings.ems_refresh_rate_hz @4 INT16U 1 RW ems settings: control_settings.ems_refresh_rate_hz (int)
active_function_count @5 INT16U 1 RO ems derived
functions.Manual_Operation.enabled @6 INT16U 1 RW ems settings: functions.Manual_Operation.enabled (bool)
functions.Manual_Operation.power_setpoint_kw @7 INT16U 1 RW ems settings: functions.Manual_Operation.power_setpoint_kw (int)
functions.Manual_Operation.ramp_rate_kw_s @8 INT16U 1 RW ems settings: functions.Manual_Operation.ramp_rate_kw_s (int)
functions.Manual_Operation.soc_limits.min_soc_pct @9 INT16U 1 RW ems settings: functions.Manual_Operation.soc_limits.min_soc_pct (int)
functions.Manual_Operation.soc_limits.max_soc_pct @10 INT16U 1 RW ems settings: functions.Manual_Operation.soc_limits.max_soc_pct (int)
functions.Manual_Operation.soc_recovery_target_pct @11 INT16U 1 RW ems settings: functions.Manual_Operation.soc_recovery_target_pct (int)
functions.Manual_Operation.power_caps_kw.charge_cap_kw @12 INT16U 1 RW ems settings: functions.Manual_Operation.power_caps_kw.charge_cap_kw (int)
functions.Manual_Operation.power_caps_kw.discharge_cap_kw @13 INT16U 1 RW ems settings: functions.Manual_Operation.power_caps_kw.discharge_cap_kw (int)
functions.Manual_Operation.telemetry_control.command_confirmation @14 INT16U 1 RW ems settings: functions.Manual_Operation.telemetry_control.command_confirmation (bool)
functions.Manual_Operation.safety.trip_on_overvoltage @15 INT16U 1 RW ems settings: functions.Manual_Operation.safety.trip_on_overvoltage (bool)
functions.Manual_Operation.safety.trip_on_undervoltage @16 INT16U 1 RW ems settings: functions.Manual_Operation.safety.trip_on_undervoltage (bool)
functions.Manual_Operation.safety.trip_on_overtemperature @17 INT16U 1 RW ems settings: functions.Manual_Operation.safety.trip_on_overtemperature (bool)
functions.Arbitrage.enabled @18 INT16U 1 RW ems settings: functions.Arbitrage.enabled (bool)
functions.Arbitrage.tick.interval_seconds @19 INT16U 1 RW ems settings: functions.Arbitrage.tick.interval_seconds (int)
functions.Arbitrage.tick.run_on_start @20 INT16U 1 RW ems settings: functions.Arbitrage.tick.run_on_start (bool)
functions.Arbitrage.tick.skip_cycles_log @21 INT16U 1 RW ems settings: functions.Arbitrage.tick.skip_cycles_log (bool)
functions.Arbitrage.tick.zero_power_on_skip @22 INT16U 1 RW ems settings: functions.Arbitrage.tick.zero_power_on_skip (bool)
functions.Arbitrage.price_source.timeout_ms @23 INT16U 1 RW ems settings: functions.Arbitrage.price_source.timeout_ms (int)
functions.Arbitrage.price_source.resolution_minutes @24 INT16U 1 RW ems settings: functions.Arbitrage.price_source.resolution_minutes (int)
functions.Arbitrage.strategy.prefer_next_slot @25 INT16U 1 RW ems settings: functions.Arbitrage.strategy.prefer_next_slot (bool)
functions.Arbitrage.strategy.min_spread @26 INT16U 1 RW ems settings: functions.Arbitrage.strategy.min_spread (int)
functions.Arbitrage.strategy.buy_threshold @27 FLOAT32 2 RW ems settings: functions.Arbitrage.strategy.buy_threshold (float)
functions.Arbitrage.strategy.sell_threshold @29 FLOAT32 2 RW ems settings: functions.Arbitrage.strategy.sell_threshold (float)
functions.Arbitrage.strategy.buy_power_kw @31 INT16U 1 RW ems settings: functions.Arbitrage.strategy.buy_power_kw (int)
functions.Arbitrage.strategy.sell_power_kw @32 INT16U 1 RW ems settings: functions.Arbitrage.strategy.sell_power_kw (int)
functions.Arbitrage.strategy.tomorrow_plan.enabled @33 INT16U 1 RW ems settings: functions.Arbitrage.strategy.tomorrow_plan.enabled (bool)
functions.Arbitrage.strategy.tomorrow_plan.charge_cheapest_slots @34 INT16U 1 RW ems settings: functions.Arbitrage.strategy.tomorrow_plan.charge_cheapest_slots (int)
functions.Arbitrage.strategy.tomorrow_plan.discharge_most_expensive_slots @35 INT16U 1 RW ems settings: functions.Arbitrage.strategy.tomorrow_plan.discharge_most_expensive_slots (int)
functions.Arbitrage.strategy.tomorrow_plan.charge_power_kw @36 INT16U 1 RW ems settings: functions.Arbitrage.strategy.tomorrow_plan.charge_power_kw (int)
functions.Arbitrage.strategy.tomorrow_plan.discharge_power_kw @37 INT16U 1 RW ems settings: functions.Arbitrage.strategy.tomorrow_plan.discharge_power_kw (int)
functions.Arbitrage.optional.hysteresis @38 INT16U 1 RW ems settings: functions.Arbitrage.optional.hysteresis (int)
functions.Arbitrage.optional.hysteresis_kw @39 INT16U 1 RW ems settings: functions.Arbitrage.optional.hysteresis_kw (int)
functions.Arbitrage.ramp_rate_kw_s @40 INT16U 1 RW ems settings: functions.Arbitrage.ramp_rate_kw_s (int)
functions.Peak_Shaving.enabled @41 INT16U 1 RW ems settings: functions.Peak_Shaving.enabled (bool)
functions.Peak_Shaving.peak_threshold_kw @42 INT16U 1 RW ems settings: functions.Peak_Shaving.peak_threshold_kw (int)
functions.Peak_Shaving.discharge_power_limit_kw @43 INT16U 1 RW ems settings: functions.Peak_Shaving.discharge_power_limit_kw (int)
functions.Peak_Shaving.min_soc_pct @44 INT16U 1 RW ems settings: functions.Peak_Shaving.min_soc_pct (int)
functions.Peak_Shaving.recovery_soc_pct @45 INT16U 1 RW ems settings: functions.Peak_Shaving.recovery_soc_pct (int)
functions.Peak_Shaving.response_time_ms @46 INT16U 1 RW ems settings: functions.Peak_Shaving.response_time_ms (int)
functions.Peak_Shaving.optional.hysteresis_kw @47 INT16U 1 RW ems settings: functions.Peak_Shaving.optional.hysteresis_kw (int)
functions.Peak_Shaving.ramp_rate_kw_s @48 INT16U 1 RW ems settings: functions.Peak_Shaving.ramp_rate_kw_s (int)
functions.Valley_Filling.enabled @49 INT16U 1 RW ems settings: functions.Valley_Filling.enabled (bool)
functions.Valley_Filling.valley_threshold_kw @50 INT16U 1 RW ems settings: functions.Valley_Filling.valley_threshold_kw (int)
functions.Valley_Filling.charge_power_limit_kw @51 INT16U 1 RW ems settings: functions.Valley_Filling.charge_power_limit_kw (int)
functions.Valley_Filling.max_soc_pct @52 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Valley_Filling.max_soc_pct (float)
functions.Valley_Filling.min_soc_pct @54 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Valley_Filling.min_soc_pct (float)
functions.Valley_Filling.response_time_ms @56 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Valley_Filling.response_time_ms (float)
functions.Valley_Filling.optional.hysteresis_kw @58 INT16U 1 RW ems settings: functions.Valley_Filling.optional.hysteresis_kw (int)
functions.Valley_Filling.ramp_rate_kw_s @59 INT16U 1 RW ems settings: functions.Valley_Filling.ramp_rate_kw_s (int)
functions.Scheduled_Charge_Discharge.enabled @60 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.enabled (bool)
functions.Scheduled_Charge_Discharge.soc_limits.min_soc_pct @61 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.soc_limits.min_soc_pct (int)
functions.Scheduled_Charge_Discharge.soc_limits.max_soc_pct @62 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.soc_limits.max_soc_pct (int)
functions.Scheduled_Charge_Discharge.power_limits.charge_power_limit_kw @63 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.power_limits.charge_power_limit_kw (int)
functions.Scheduled_Charge_Discharge.power_limits.discharge_power_limit_kw @64 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.power_limits.discharge_power_limit_kw (int)
functions.Scheduled_Charge_Discharge.response_time_ms @65 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.response_time_ms (int)
functions.Scheduled_Charge_Discharge.validation.prevent_overlaps @66 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.validation.prevent_overlaps (bool)
functions.Scheduled_Charge_Discharge.validation.min_duration_minutes @67 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.validation.min_duration_minutes (int)
functions.Scheduled_Charge_Discharge.ramp_rate_kw_s @68 INT16U 1 RW ems settings: functions.Scheduled_Charge_Discharge.ramp_rate_kw_s (int)
functions.Backup.enabled @69 INT16U 1 RW ems settings: functions.Backup.enabled (bool)
functions.Backup.backup_power_setpoint_kw @70 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Backup.backup_power_setpoint_kw (float)
functions.Backup.min_soc_pct @72 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Backup.min_soc_pct (float)
functions.Backup.recovery_soc_pct @74 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Backup.recovery_soc_pct (float)
functions.Backup.response_time_ms @76 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Backup.response_time_ms (float)
functions.Backup.black_start_enable @78 INT16U 1 RW ems settings: functions.Backup.black_start_enable (bool)
functions.Backup.grid_mode_switch.enabled @79 INT16U 1 RW ems settings: functions.Backup.grid_mode_switch.enabled (bool)
functions.Backup.grid_mode_switch.grid_loss_voltage_v @80 INT16U 1 RW ems settings: functions.Backup.grid_mode_switch.grid_loss_voltage_v (int)
functions.Backup.grid_mode_switch.grid_loss_frequency_hz_low @81 INT16U 1 RW ems settings: functions.Backup.grid_mode_switch.grid_loss_frequency_hz_low (int)
functions.Backup.grid_mode_switch.grid_loss_frequency_hz_high @82 INT16U 1 RW ems settings: functions.Backup.grid_mode_switch.grid_loss_frequency_hz_high (int)
functions.Backup.grid_mode_switch.switch_delay_s @83 INT16U 1 RW ems settings: functions.Backup.grid_mode_switch.switch_delay_s (int)
functions.Backup.power_dispatch.enabled @84 INT16U 1 RW ems settings: functions.Backup.power_dispatch.enabled (bool)
functions.Backup.ramp_rate_kw_s @85 INT16U 1 RW ems settings: functions.Backup.ramp_rate_kw_s (int)
functions.Backup_Peak_Shaving.enabled @86 INT16U 1 RW ems settings: functions.Backup_Peak_Shaving.enabled (bool)
functions.Backup_Frequency_Regulation.enabled @87 INT16U 1 RW ems settings: functions.Backup_Frequency_Regulation.enabled (bool)
functions.Power_Factor_Correction.enabled @88 INT16U 1 RW ems settings: functions.Power_Factor_Correction.enabled (bool)
functions.Power_Factor_Correction.target_pf @89 FLOAT32 2 RW ems settings: functions.Power_Factor_Correction.target_pf (float)
functions.Power_Factor_Correction.pf_deadband @91 FLOAT32 2 RW ems settings: functions.Power_Factor_Correction.pf_deadband (float)
functions.Power_Factor_Correction.q_max_kvar @93 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.q_max_kvar (float)
functions.Power_Factor_Correction.ramp_rate_limit_kvar_s @95 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.ramp_rate_limit_kvar_s (float)
functions.Power_Factor_Correction.response_time_ms @97 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.response_time_ms (float)
functions.Power_Factor_Correction.soc_limits.min_soc_pct @99 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.soc_limits.min_soc_pct (float)
functions.Power_Factor_Correction.soc_limits.max_soc_pct @101 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.soc_limits.max_soc_pct (float)
functions.Power_Factor_Correction.power_caps_kw.charge_cap_kw @103 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.power_caps_kw.charge_cap_kw (float)
functions.Power_Factor_Correction.power_caps_kw.discharge_cap_kw @105 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.power_caps_kw.discharge_cap_kw (float)
functions.Power_Factor_Correction.reactive_power_actuation.enabled @107 INT16U 1 RW ems settings: functions.Power_Factor_Correction.reactive_power_actuation.enabled (bool)
functions.Power_Factor_Correction.reactive_power_actuation.register @108 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.reactive_power_actuation.register (float)
functions.Power_Factor_Correction.reactive_power_actuation.scale_kvar_per_unit @110 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.reactive_power_actuation.scale_kvar_per_unit (float)
functions.Power_Factor_Correction.reactive_power_actuation.rated_kva @112 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Power_Factor_Correction.reactive_power_actuation.rated_kva (float)
functions.Voltage_Support.enabled @114 INT16U 1 RW ems settings: functions.Voltage_Support.enabled (bool)
functions.Voltage_Support.nominal_voltage_v @115 INT16U 1 RW ems settings: functions.Voltage_Support.nominal_voltage_v (int)
functions.Voltage_Support.v_low_pu @116 FLOAT32 2 RW ems settings: functions.Voltage_Support.v_low_pu (float)
functions.Voltage_Support.v1_pu @118 FLOAT32 2 RW ems settings: functions.Voltage_Support.v1_pu (float)
functions.Voltage_Support.v2_pu @120 FLOAT32 2 RW ems settings: functions.Voltage_Support.v2_pu (float)
functions.Voltage_Support.v_high_pu @122 FLOAT32 2 RW ems settings: functions.Voltage_Support.v_high_pu (float)
functions.Voltage_Support.q_max_kvar @124 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.q_max_kvar (float)
functions.Voltage_Support.ramp_rate_limit_kvar_s @126 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.ramp_rate_limit_kvar_s (float)
functions.Voltage_Support.response_time_ms @128 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.response_time_ms (float)
functions.Voltage_Support.soc_limits.min_soc_pct @130 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.soc_limits.min_soc_pct (float)
functions.Voltage_Support.soc_limits.max_soc_pct @132 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.soc_limits.max_soc_pct (float)
functions.Voltage_Support.power_caps_kw.charge_cap_kw @134 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.power_caps_kw.charge_cap_kw (float)
functions.Voltage_Support.power_caps_kw.discharge_cap_kw @136 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.power_caps_kw.discharge_cap_kw (float)
functions.Voltage_Support.reactive_power_actuation.enabled @138 INT16U 1 RW ems settings: functions.Voltage_Support.reactive_power_actuation.enabled (bool)
functions.Voltage_Support.reactive_power_actuation.register @139 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.reactive_power_actuation.register (float)
functions.Voltage_Support.reactive_power_actuation.scale_kvar_per_unit @141 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.reactive_power_actuation.scale_kvar_per_unit (float)
functions.Voltage_Support.reactive_power_actuation.rated_kva @143 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: functions.Voltage_Support.reactive_power_actuation.rated_kva (float)
functions.Frequency_Regulation.enabled @145 INT16U 1 RW ems settings: functions.Frequency_Regulation.enabled (bool)
functions.Frequency_Regulation.droop_pct @146 INT16U 1 RW ems settings: functions.Frequency_Regulation.droop_pct (int)
functions.Frequency_Regulation.deadband_hz @147 FLOAT32 2 RW ems settings: functions.Frequency_Regulation.deadband_hz (float)
functions.Frequency_Regulation.participation_pct @149 INT16U 1 RW ems settings: functions.Frequency_Regulation.participation_pct (int)
functions.Frequency_Regulation.response_time_ms @150 INT16U 1 RW ems settings: functions.Frequency_Regulation.response_time_ms (int)
functions.Frequency_Regulation.ramp_rate_limit_kw_s @151 INT16U 1 RW ems settings: functions.Frequency_Regulation.ramp_rate_limit_kw_s (int)
functions.Frequency_Regulation.soc_limits.min_soc_pct @152 INT16U 1 RW ems settings: functions.Frequency_Regulation.soc_limits.min_soc_pct (int)
functions.Frequency_Regulation.soc_limits.max_soc_pct @153 INT16U 1 RW ems settings: functions.Frequency_Regulation.soc_limits.max_soc_pct (int)
functions.Frequency_Regulation.soc_recovery_target_pct @154 INT16U 1 RW ems settings: functions.Frequency_Regulation.soc_recovery_target_pct (int)
functions.Frequency_Regulation.power_caps_kw.charge_cap_kw @155 INT16U 1 RW ems settings: functions.Frequency_Regulation.power_caps_kw.charge_cap_kw (int)
functions.Frequency_Regulation.power_caps_kw.discharge_cap_kw @156 INT16U 1 RW ems settings: functions.Frequency_Regulation.power_caps_kw.discharge_cap_kw (int)
functions.Frequency_Regulation.frequency_measurement_interval_ms @157 INT16U 1 RW ems settings: functions.Frequency_Regulation.frequency_measurement_interval_ms (int)
functions.Frequency_Regulation.telemetry_api.send_frequency_ms @158 INT16U 1 RW ems settings: functions.Frequency_Regulation.telemetry_api.send_frequency_ms (int)
functions.Frequency_Regulation.telemetry_api.timeout_ms @159 INT16U 1 RW ems settings: functions.Frequency_Regulation.telemetry_api.timeout_ms (int)
functions.Frequency_Regulation.telemetry_api.retry_policy.retries @160 INT16U 1 RW ems settings: functions.Frequency_Regulation.telemetry_api.retry_policy.retries (int)
functions.Frequency_Regulation.telemetry_api.retry_policy.backoff_ms @161 INT16U 1 RW ems settings: functions.Frequency_Regulation.telemetry_api.retry_policy.backoff_ms (int)
functions.Frequency_Regulation.logging.enabled @162 INT16U 1 RW ems settings: functions.Frequency_Regulation.logging.enabled (bool)
functions.Frequency_Regulation.logging.flush_interval_ms @163 INT16U 1 RW ems settings: functions.Frequency_Regulation.logging.flush_interval_ms (int)
functions.Frequency_Regulation.logging.max_batch_records @164 INT16U 1 RW ems settings: functions.Frequency_Regulation.logging.max_batch_records (int)
functions.Frequency_Regulation.logging.rotate_every_seconds @165 INT16U 1 RW ems settings: functions.Frequency_Regulation.logging.rotate_every_seconds (int)
functions.Frequency_Regulation.soc_source.refresh_interval_ms @166 INT16U 1 RW ems settings: functions.Frequency_Regulation.soc_source.refresh_interval_ms (int)
functions.Frequency_Regulation.nominal_hz @167 INT16U 1 RW ems settings: functions.Frequency_Regulation.nominal_hz (int)
functions.Anti_Backflow.enabled @168 INT16U 1 RW ems settings: functions.Anti_Backflow.enabled (bool)
functions.Anti_Backflow.export_limit_kw @169 INT16U 1 RW ems settings: functions.Anti_Backflow.export_limit_kw (int)
functions.Anti_Backflow.response_time_ms @170 INT16U 1 RW ems settings: functions.Anti_Backflow.response_time_ms (int)
functions.Anti_Backflow.ramp_rate_limit_kw_s @171 INT16U 1 RW ems settings: functions.Anti_Backflow.ramp_rate_limit_kw_s (int)
functions.Anti_Backflow.soc_limits.min_soc_pct @172 INT16U 1 RW ems settings: functions.Anti_Backflow.soc_limits.min_soc_pct (int)
functions.Anti_Backflow.soc_limits.max_soc_pct @173 INT16U 1 RW ems settings: functions.Anti_Backflow.soc_limits.max_soc_pct (int)
functions.Anti_Backflow.ramp_rate_kw_s @174 INT16U 1 RW ems settings: functions.Anti_Backflow.ramp_rate_kw_s (int)
functions.Maintenance.hold_zero_power @175 INT16U 1 RW ems settings: functions.Maintenance.hold_zero_power (bool)
functions.Energy_Optimization.enabled @176 INT16U 1 RW ems settings: functions.Energy_Optimization.enabled (bool)
functions.Power_Node_Energy_Sharing.enabled @177 INT16U 1 RW ems settings: functions.Power_Node_Energy_Sharing.enabled (bool)
functions.Grid_Sync.enabled @178 INT16U 1 RW ems settings: functions.Grid_Sync.enabled (bool)
functions.Dynamic_Load_Balancing.enabled @179 INT16U 1 RW ems settings: functions.Dynamic_Load_Balancing.enabled (bool)
protections.overvoltage_v @180 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.overvoltage_v (float)
protections.undervoltage_v @182 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.undervoltage_v (float)
protections.overcurrent_a @184 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.overcurrent_a (float)
protections.over_frequency_hz @186 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.over_frequency_hz (float)
protections.under_frequency_hz @188 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.under_frequency_hz (float)
protections.temperature_thresholds.cell_max_c @190 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.temperature_thresholds.cell_max_c (float)
protections.temperature_thresholds.pcs_max_c @192 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.temperature_thresholds.pcs_max_c (float)
protections.temperature_thresholds.cabinet_max_c @194 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.temperature_thresholds.cabinet_max_c (float)
protections.temperature_thresholds.cell_min_c @196 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.temperature_thresholds.cell_min_c (float)
protections.temperature_thresholds.pcs_min_c @198 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.temperature_thresholds.pcs_min_c (float)
protections.temperature_thresholds.cabinet_min_c @200 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.temperature_thresholds.cabinet_min_c (float)
protections.fire_suppression_integration @202 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.fire_suppression_integration (float)
protections.ems_bms_comm_timeout_ms @204 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: protections.ems_bms_comm_timeout_ms (float)
monitoring_logging.data_push_interval_ms @206 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: monitoring_logging.data_push_interval_ms (float)
monitoring_logging.logging_level @208 FLOAT32 2 RW ems unset in the settings file (serves 0); settings: monitoring_logging.logging_level (float)