Skip to content

Auxiliary device registers

Generated from EnergySyc_EMS_ES100Cx12S/emsConfig/ems/ems_register_full.json by EnergySyc_EMS_ES100Cx12S/tools/generate_register_map_docs.py. Do not edit by hand - re-run the generator after changing the register map.

UPS (ups1)

54 registers, @31980..@32060, source map ups/ups1/ups_register_full___ups_10k.json.

Register Address Type Regs Access Device Notes
input_voltage_l1_v @31980 FLOAT32 2 RO ups1 -
input_voltage_l2_v @31982 FLOAT32 2 RO ups1 -
input_voltage_l3_v @31984 FLOAT32 2 RO ups1 -
input_current_l1_a @31986 FLOAT32 2 RO ups1 -
input_current_l2_a @31988 FLOAT32 2 RO ups1 -
input_current_l3_a @31990 FLOAT32 2 RO ups1 -
input_frequency_hz @31992 FLOAT32 2 RO ups1 -
input_power_factor @31994 FLOAT32 2 RO ups1 -
input_voltage_thd_percent @31996 FLOAT32 2 RO ups1 -
input_energy_kwh @31998 FLOAT32 2 RO ups1 -
output_voltage_l1_v @32000 FLOAT32 2 RO ups1 -
output_voltage_l2_v @32002 FLOAT32 2 RO ups1 -
output_voltage_l3_v @32004 FLOAT32 2 RO ups1 -
output_current_l1_a @32006 FLOAT32 2 RO ups1 -
output_current_l2_a @32008 FLOAT32 2 RO ups1 -
output_current_l3_a @32010 FLOAT32 2 RO ups1 -
output_frequency_hz @32012 FLOAT32 2 RO ups1 -
output_active_power_kw @32014 FLOAT32 2 RO ups1 -
output_apparent_power_kva @32016 FLOAT32 2 RO ups1 -
output_load_percent @32018 FLOAT32 2 RO ups1 -
battery_voltage_v @32020 FLOAT32 2 RO ups1 -
battery_current_a @32022 FLOAT32 2 RO ups1 -
battery_temperature_c @32024 FLOAT32 2 RO ups1 -
battery_capacity_percent @32026 FLOAT32 2 RO ups1 -
battery_runtime_min @32028 INT16U 1 RO ups1 -
battery_charge_state_percent @32029 INT16U 1 RO ups1 -
battery_health_percent @32030 INT16U 1 RO ups1 -
battery_cycles @32031 INT16U 1 RO ups1 -
battery_cell_count @32032 INT16U 1 RO ups1 -
battery_string_voltage_v @32033 FLOAT32 2 RO ups1 -
ups_operating_mode @32035 ENUM16 1 RO ups1 -
input_line_fail @32036 BOOL16 1 RO ups1 -
on_battery @32037 BOOL16 1 RO ups1 -
bypass_active @32038 BOOL16 1 RO ups1 -
battery_low @32039 BOOL16 1 RO ups1 -
overload @32040 BOOL16 1 RO ups1 -
overtemperature @32041 BOOL16 1 RO ups1 -
output_short_circuit @32042 BOOL16 1 RO ups1 -
rectifier_running @32043 BOOL16 1 RO ups1 -
inverter_running @32044 BOOL16 1 RO ups1 -
eco_mode_active @32045 BOOL16 1 RO ups1 -
maintenance_bypass @32046 BOOL16 1 RO ups1 -
ups_fault @32047 BOOL16 1 RO ups1 -
fan_fault @32048 BOOL16 1 RO ups1 -
communication_ok @32049 BOOL16 1 RO ups1 -
output_switch_on @32050 BOOL16 1 RO ups1 -
alarm_bitmap @32051 BITMAP32 2 RO ups1 -
fault_code @32053 INT16U 1 RO ups1 -
alarm_count @32054 INT16U 1 RO ups1 -
output_voltage_setpoint_v @32055 FLOAT32 2 RW ups1 -
battery_low_threshold_percent @32057 INT16U 1 RW ups1 -
shutdown_delay_min @32058 INT16U 1 RW ups1 -
battery_test_start @32059 BOOL16 1 RW ups1 -
buzzer_enable @32060 BOOL16 1 RW ups1 -

Air conditioning (ac1)

56 registers, @25000..@25084, source map air_condition_unit/ac1/ac_register_full___ac_std.json.

Register Address Type Regs Access Device Notes
room_temp_c @25000 FLOAT32 2 RO ac1 -
supply_air_temp_c @25002 FLOAT32 2 RO ac1 -
return_air_temp_c @25004 FLOAT32 2 RO ac1 -
evap_inlet_temp_c @25006 FLOAT32 2 RO ac1 -
evap_outlet_temp_c @25008 FLOAT32 2 RO ac1 -
cond_inlet_temp_c @25010 FLOAT32 2 RO ac1 -
cond_outlet_temp_c @25012 FLOAT32 2 RO ac1 -
outdoor_temp_c @25014 FLOAT32 2 RO ac1 -
suction_line_temp_c @25016 FLOAT32 2 RO ac1 -
discharge_line_temp_c @25018 FLOAT32 2 RO ac1 -
suction_pressure_kpa @25020 FLOAT32 2 RO ac1 -
discharge_pressure_kpa @25022 FLOAT32 2 RO ac1 -
room_rh_percent @25024 FLOAT32 2 RO ac1 -
return_rh_percent @25026 FLOAT32 2 RO ac1 -
cooling_setpoint_c @25028 FLOAT32 2 RW ac1 -
heating_setpoint_c @25030 FLOAT32 2 RW ac1 -
supply_air_setpoint_c @25032 FLOAT32 2 RW ac1 -
humidity_setpoint_percent @25034 FLOAT32 2 RW ac1 -
deadband_c @25036 FLOAT32 2 RW ac1 -
fan_speed_percent @25038 FLOAT32 2 RW ac1 -
fan_mode @25040 ENUM16 1 RW ac1 values: 1 = Auto, 2 = Low, 3 = Medium, 4 = High
system_mode @25041 ENUM16 1 RW ac1 values: 0 = Off, 1 = Cool, 2 = Heat, 3 = Dry, 4 = FanOnly, 5 = Auto
occupancy_mode @25042 ENUM16 1 RW ac1 values: 0 = Unoccupied, 1 = Occupied
unit_running @25043 INT16U 1 RO ac1 -
compressor1_running @25044 INT16U 1 RO ac1 -
compressor2_running @25045 INT16U 1 RO ac1 -
economizer_active @25046 INT16U 1 RO ac1 -
defrost_active @25047 INT16U 1 RO ac1 -
fault_active @25048 INT16U 1 RO ac1 -
supply_fan_running @25049 INT16U 1 RO ac1 -
return_fan_running @25050 INT16U 1 RO ac1 -
alarm_bitmap_1 @25051 BITMAP32 2 RO ac1 -
high_pressure_trip_count @25053 INT16U 1 RO ac1 -
low_pressure_trip_count @25054 INT16U 1 RO ac1 -
high_temp_alarm_count @25055 INT16U 1 RO ac1 -
low_temp_alarm_count @25056 INT16U 1 RO ac1 -
sensor_fault_count @25057 INT16U 1 RO ac1 -
active_power_kw @25058 FLOAT32 2 RO ac1 -
energy_consumed_kwh @25060 FLOAT32 2 RO ac1 -
demand_kw @25062 FLOAT32 2 RO ac1 -
compressor1_hours @25064 FLOAT32 2 RO ac1 -
compressor2_hours @25066 FLOAT32 2 RO ac1 -
fan_hours @25068 FLOAT32 2 RO ac1 -
digital_output_1_command @25070 BOOL16 1 RW ac1 -
digital_output_2_command @25071 BOOL16 1 RW ac1 -
analog_output_1_percent @25072 FLOAT32 2 RW ac1 -
analog_output_2_percent @25074 FLOAT32 2 RW ac1 -
digital_input_1_status @25076 BOOL16 1 RO ac1 -
digital_input_2_status @25077 BOOL16 1 RO ac1 -
command_on_off @25078 ENUM16 1 RW ac1 values: 0 = Off, 1 = On, 2 = Toggle
command_reset_alarms @25079 ENUM16 1 RW ac1 values: 0 = NoOp, 1 = Reset
command_force_defrost @25080 ENUM16 1 RW ac1 values: 0 = Stop, 1 = Start
protocol_version @25081 INT16U 1 RO ac1 -
firmware_version_major @25082 INT16U 1 RO ac1 -
firmware_version_minor @25083 INT16U 1 RO ac1 -
device_address @25084 INT16U 1 RO ac1 -

Cooling unit (cooling1)

35 registers, @26968..@27024, source map liquid_cooling_unit/cooling1/cooling_register_full___cool_std.json.

Register Address Type Regs Access Device Notes
supply_temp_c @26968 FLOAT32 2 RO cooling1 -
return_temp_c @26970 FLOAT32 2 RO cooling1 -
ambient_temp_c @26972 FLOAT32 2 RO cooling1 -
coolant_inlet_temp_c @26974 FLOAT32 2 RO cooling1 -
coolant_outlet_temp_c @26976 FLOAT32 2 RO cooling1 -
compressor_temp_c @26978 FLOAT32 2 RO cooling1 -
condenser_temp_c @26980 FLOAT32 2 RO cooling1 -
evaporator_temp_c @26982 FLOAT32 2 RO cooling1 -
setpoint_temp_c @26984 FLOAT32 2 RW cooling1 -
min_temp_limit_c @26986 FLOAT32 2 RW cooling1 -
max_temp_limit_c @26988 FLOAT32 2 RW cooling1 -
operating_mode @26990 UINT16 1 RW cooling1 -
setpoint_temp_apply @26991 FLOAT32 2 RW cooling1 -
water_flow_rate_lpm @26993 FLOAT32 2 RO cooling1 -
system_pressure_bar @26995 FLOAT32 2 RO cooling1 -
refrigerant_pressure_bar @26997 FLOAT32 2 RO cooling1 -
running @26999 BOOL 1 RO cooling1 -
compressor_on @27000 BOOL 1 RO cooling1 -
fan_on @27001 BOOL 1 RO cooling1 -
pump_on @27002 BOOL 1 RO cooling1 -
maintenance_required @27003 BOOL 1 RO cooling1 -
leak_detected @27004 BOOL 1 RO cooling1 -
alarm_code @27005 UINT16 1 RO cooling1 -
alarm_bitmap @27006 BITMAP32 2 RO cooling1 -
high_pressure_alarm @27008 BOOL 1 RO cooling1 -
low_flow_alarm @27009 BOOL 1 RO cooling1 -
over_temperature_alarm @27010 BOOL 1 RO cooling1 -
cooling_power_kw @27011 FLOAT32 2 RO cooling1 -
energy_consumed_kwh @27013 FLOAT32 2 RO cooling1 -
compressor_speed_rpm @27015 FLOAT32 2 RO cooling1 -
fan_speed_rpm @27017 FLOAT32 2 RO cooling1 -
runtime_hours @27019 FLOAT32 2 RO cooling1 -
compressor_runtime_hours @27021 FLOAT32 2 RO cooling1 -
comm_status @27023 UINT16 1 RO cooling1 -
heartbeat @27024 UINT16 1 RO cooling1 -

Fire suppression (fss1)

55 registers, @26390..@26459, source map fire_safety_system/fss1/fss_register_full___fss_std.json.

Register Address Type Regs Access Device Notes
gas_detector_ppm @26390 FLOAT32 2 RO fss1 -
smoke_obscuration_percent @26392 FLOAT32 2 RO fss1 -
heat_detector_temp_c @26394 FLOAT32 2 RO fss1 -
ambient_temp_c @26396 FLOAT32 2 RO fss1 -
aerosol_canister_pressure_kpa @26398 FLOAT32 2 RO fss1 -
aerosol_canister_remaining_percent @26400 FLOAT32 2 RO fss1 -
gas_pre_alarm_ppm @26402 FLOAT32 2 RW fss1 -
gas_alarm_ppm @26404 FLOAT32 2 RW fss1 -
smoke_pre_alarm_obscuration_percent @26406 FLOAT32 2 RW fss1 -
smoke_alarm_obscuration_percent @26408 FLOAT32 2 RW fss1 -
heat_pre_alarm_temp_c @26410 FLOAT32 2 RW fss1 -
heat_alarm_temp_c @26412 FLOAT32 2 RW fss1 -
release_delay_s @26414 INT16U 1 RW fss1 -
discharge_duration_s @26415 INT16U 1 RW fss1 -
cross_zone_logic @26416 ENUM16 1 RW fss1 values: 0 = AnyOne, 1 = TwoOfThree, 2 = GasOrSmoke, 3 = GasAndSmoke, 4 = HeatOnly, 5 = ManualOnly
manual_release_enable @26417 BOOL16 1 RW fss1 -
inhibit_release @26418 BOOL16 1 RW fss1 -
abort_enabled @26419 BOOL16 1 RW fss1 -
hush_duration_s @26420 INT16U 1 RW fss1 -
auto_reset_enabled @26421 BOOL16 1 RW fss1 -
system_state @26422 ENUM16 1 RO fss1 values: 0 = Idle, 1 = PreAlarm, 2 = Alarm, 3 = PreDischarge, 4 = Discharging, 5 = Released, 6 = Fault, 7 = Inhibit
gas_alarm_active @26423 BOOL16 1 RO fss1 -
smoke_alarm_active @26424 BOOL16 1 RO fss1 -
heat_alarm_active @26425 BOOL16 1 RO fss1 -
cross_zone_met @26426 BOOL16 1 RO fss1 -
actuator_ready @26427 BOOL16 1 RO fss1 -
actuator_fired @26428 BOOL16 1 RO fss1 -
abort_active @26429 BOOL16 1 RO fss1 -
manual_release_active @26430 BOOL16 1 RO fss1 -
fault_bitmap @26431 BITMAP32 2 RO fss1 -
alarm_bitmap @26433 BITMAP32 2 RO fss1 -
fault_counts_total @26435 INT16U 1 RO fss1 -
gas_alarm_count @26436 INT16U 1 RO fss1 -
smoke_alarm_count @26437 INT16U 1 RO fss1 -
heat_alarm_count @26438 INT16U 1 RO fss1 -
release_count @26439 INT16U 1 RO fss1 -
last_event_code @26440 ENUM16 1 RO fss1 -
last_event_epoch_s @26441 INT32U 2 RO fss1 -
maintenance_due_days @26443 INT16U 1 RO fss1 -
input_abort_button @26444 BOOL16 1 RO fss1 -
input_manual_release @26445 BOOL16 1 RO fss1 -
input_door_interlock @26446 BOOL16 1 RO fss1 -
input_service_key @26447 BOOL16 1 RO fss1 -
sounder_command @26448 ENUM16 1 RW fss1 values: 0 = Off, 1 = On, 2 = Silence, 3 = Test
strobe_enable @26449 BOOL16 1 RW fss1 -
command_system_reset @26450 ENUM16 1 RW fss1 values: 0 = NoOp, 1 = Reset
command_acknowledge @26451 ENUM16 1 RW fss1 values: 0 = NoOp, 1 = Ack
command_silence_sounder @26452 ENUM16 1 RW fss1 values: 0 = NoOp, 1 = Silence
command_manual_release @26453 ENUM16 1 RW fss1 values: 0 = NoOp, 1 = Fire
command_inhibit_toggle @26454 ENUM16 1 RW fss1 values: 0 = Off, 1 = On, 2 = Toggle
command_test_mode @26455 ENUM16 1 RW fss1 values: 0 = Exit, 1 = Enter
protocol_version @26456 INT16U 1 RO fss1 -
firmware_version_major @26457 INT16U 1 RO fss1 -
firmware_version_minor @26458 INT16U 1 RO fss1 -
device_address @26459 INT16U 1 RO fss1 -

Sensor block (sensor_block1)

7 registers, @31669..@31681, source map sensor_block/sensorB1/sensorB_register_full___sens_std.json.

Register Address Type Regs Access Device Notes
humidity_sensor_1_percent @31669 FLOAT32 2 RO sensor_block1 -
humidity_sensor_2_percent @31671 FLOAT32 2 RO sensor_block1 -
light_sensor_1_lux @31673 FLOAT32 2 RO sensor_block1 -
light_sensor_2_lux @31675 FLOAT32 2 RO sensor_block1 -
light_sensor_3_lux @31677 FLOAT32 2 RO sensor_block1 -
light_sensor_4_lux @31679 FLOAT32 2 RO sensor_block1 -
alarm_activation_relay @31681 BOOL16 1 RW sensor_block1 -